Browse technical resources about smart energy, digital platforms, and optimization systems.
In February 2024, the government extended VAT relief on solar batteries. They're currently zero-rated for VAT regardless of when they're installed. VAT on electricity and gas used by households is 5%.
The 0% VAT rate applies to a range of energy-saving materials and technologies beyond solar panels. These include ground and air source heat pumps, insulation materials, wind and water turbines, and controls for central heating and hot water systems.
However, to support certain industry sectors, such as hospitality and tourism, a lower rate of 5% is applied. For several years, the Renewable Energy Sector has also benefited from this reduced tax rate. Although helpful in numerous ways, many households pay an extra cost when purchasing energy-efficient equipment such as solar panels.
Solar batteries installed alongside solar panels have been eligible for the 0% VAT rate since the policy's introduction in April 2022. As of February 1, 2024, the VAT exemption has been expanded to include standalone battery installations and retrofitted batteries.
This depends on the number of panels included and the wattage of electricity it generates. The 0% VAT Relief is already applied to these prices. After March 2027, the prices will rise again to include a 5% VAT increase. This means, based on current prices, customers will be paying hundreds of pounds more for the same system in the future.
Currently, there is no VAT on solar panel installations for residential properties in the UK. This zero-rate VAT policy was introduced in April 2022 for England, Scotland, and Wales, and extended to Northern Ireland from May 2023. The 0% VAT rate applies to both the cost of solar panels and their installation. When will this VAT exemption end?
The 0% VAT rate can lead to substantial financial benefits for homeowners investing in solar technology. According to Sunsave, for a typical 3.5 kilowatt peak (kWp) solar and battery system in a three-bedroom home, the savings are significant: Total System Cost: Approximately £9,000 with 0% VAT. Previous Cost with 20% VAT: Roughly £10,800.
They can lease their land for a pv solar farm, install an agricultural solar system on farm buildings, or adopt agrivoltaics—a method that combines agriculture with solar energy.
Farmers can benefit from solar energy in several ways—by leasing farmland for solar; installing a solar system on a house, barn, or other building; or through agrivoltaics. Agrivoltaics is defined as agriculture, such as crop production, livestock grazing, and pollinator habitat, located underneath solar panels and/or between rows of solar panels.
Solar panels can increase your operation's profitability. One government grant program for solar panels on farms is called the Rural Energy for America Program (REAP). Why solar energy may be a good fit for your farmers and ranchers Tips and funding opportunities for solar projects on your farm
The future looks bright for farmers considering solar panels for farms! With numerous benefits ranging from cost savings to environmental sustainability, going solar is an investment worth making.
When selecting a provider for solar panels for farms, consider their experience in agricultural installations and customer reviews regarding product quality and support services. Conclusion: Embracing Solar Panels for Sustainable Farming The future looks bright for farmers considering solar panels for farms!
Here's why farmers and rural property owners choose solar: Solar panels allow farmers to significantly cut their electricity expenses by generating their own power. With solar energy, farms can offset a substantial portion of their electricity usage, lowering overall operating costs.
Solar panels can be incorporated into the design of carports and equipment sheds, providing both energy generation and covered storage for farm vehicles and machinery. This dual-purpose approach maximizes the utility of farm structures. Installing solar on agricultural buildings can present unique challenges. Here's how we at 8MSolar address them:
In 2024, the solar energy industry is expected to witness a surge of innovative MPPT-based charge controller technologies. These advancements will optimize power conversion efficiency, enhance system reliability, and cater to the evolving needs of renewable energy installations.
As renewable energy continues to gain momentum, it is expected that EV charging will begin to integrate with renewable energy sources. By 2024, it is anticipated that renewable energy sources like solar will be used to power EV charging stations, creating a completely sustainable charging option. 4. Vehicle-to-Grid Technology Should Expand
The electric vehicle charging industry has seen significant changes in 2023, and experts predict the top 6 EV charging trends for 2024 that will shape the coming year. These trends include increased demand for fast-charging stations, expanded use of renewable energy sources, and improvements in battery technology.
One of the most important factors for EV adoption is convenience for users. In 2024, we can expect EV charging stations to provide even greater convenience, including payment options like mobile payments and even automatic payments integrated into the EV itself.
Sign up for daily news updates from CleanTechnica on email. Or follow us on Google News! SolarEdge is known for high efficiency inverters, and the company was at RE+ 2024 in Anaheim, California, again this year showing off all the latest improvements and upgrades it has made to its home solar ecosystem of products.
At Intersolar Europe, SolarEdge revealed its new Bi-Directional DC EV Charger. The charger allows solar-powered V2H and V2G operations.
The new charger will enable solar-powered Vehicle-to-Home (V2H) and Vehicle-to-Grid (V2G) functionalities and is expected to be commercially available in the second half of 2024. Based on SolarEdge's innovative DC-coupled architecture, the Charger is expected to offer several benefits:
Owing to the strict restrictions imposed by the Marine Pollution Protocol and the rapid development of renewable energy, the use of solar generation and energy storage systems in ship power systems has been incre. ••An optimal sizing method is developed for a hybrid PV/diesel/ESS ship. As the amount of greenhouse gas that is produced by the ship systems increases, the International Convention for the Prevention of Pollution from Ships (MARPOL) re. 2.1. Difference between standalone power systems on land and hybrid ship power systemsThe studied problem related to the generation expan. 3.1. Objective functionBased on the above description, the objective of the studied problem is to minimize the investment and operating costs of the ship'. Since the optimal sizing problem is formulated as a constrained nonlinear optimization problem, Multi-Objective Particle Swarm Optimization (MOPSO) combined with eli.
[PDF Version]Output power of PV panels on board. It can be seen from Fig. 3 that the average power output of PV system is 137.18 kW, which is also the expected value injected into the ship's power system. With the change of the solar irradiation and tilt angel, the HESS will smooth the variations in the power output.
The impacts of the integration of solar power into a ship's power system, different loading conditions, and energy storage systems are studied to demonstrate the effectiveness of the proposed MOPSO method. Case 1: A cost study considering the diesel generator only. Case 2: A cost only considering the diesel generator and PV array only.
4.1.1. Solar/battery powered ships Solar/battery power system is the typical power system configuration for medium and small-scale solar-powered ships. The “Sun 21” (Fig. 9 a) was the world's first solar-powered ship to cross the Atlantic in 2006, with 65 m 2 PV panels between the hull to supply the ship power system .
An optimal sizing method is developed for a hybrid PV/diesel/ESS ship power system. The output of PV along a navigation route is explored for the ship power system. Five operating conditions of the load in the ship power system are modeled. The impact of various prices of PV on cost is studied.
“Emerald Ace” (Fig. 9 f) is another ocean-going solar-powered ship with 768 PV panels rated at 160 kW . In addition, the “Tengfei” solar-powered ocean-going car carrier and the “Anji204” solar-powered inland river car carrier are two typical large-scale solar-powered ships in China. These solar-powered ships are summarized in Table 2. Table 2.
New energy sources, including solar energy, wind energy and fuel cells have already been introduced into ship power system. Solar energy can now be used as the main power source to propel small-scale ships, and as an auxiliary power source in large-scale ships to supply lighting, communication devices and navigation system.
The literature on China's renewable energy policy has grown significantly as China has become a world leader in global solar PV industry. While early studies explored the effect of subsidies on the solar industry, more recent research has focused on the effect of market factors on investments.
The data on practitioners in the PV power generation industry are obtained through appropriate calculations. In the period of 2011–2017, China's solar PVs accounted for 0.01%, 0.07%, 0.16%, 0.42%, 0.69%,1.1%, and 1.82% of the total power generation, respectively.
This is the first study to assess the wind and solar power potential in a unified manner at provincial level in China. China has sufficient renewable power potential to support its carbon neutrality vision, but unevenly distributed spatially.
This will promote the development of the PV industry from another aspect. The theoretical reserves of solar energy and the efficiency of PV power generation shows a positive correlation, and the richer the light resources, the higher the PV power generation efficiency.
As previously discussed, the solar PV power potential is higher in less-developed northwest China, and these regions with better resource endowments attracted a significant share of UPV investments during the period analyzed. However, low levels of industrialization in these provinces contribute to lower overall consumption of electricity. 6.
Studies have been conducted to assess wind and solar energy resources both globally and specifically in China (Table 1). On the whole, there have been more assessments of onshore wind and solar resources than offshore wind resources. Both technical potential and economic potential are widely used indicators in resource assessments. Table 1.
According to the IEA estimates, recent supply chain problems and freight costs have increased utility-scale solar PV CAPEX by approximately 25%, which may adversely affect new investments in China (IEA, 2021b). 5.3. Co-opetition relationship between UPV and DPV
Solar energy is not only vital for the generation of renewable energy sources but also plays a crucial role in maintaining the natural balance within ecosystems. It influences various ecological processes that are essential for ecosystem sustainability and overall health.
Energy tied with the matter (biomass/nutrients) flows through an ecosystem via various trophic levels – from producers to top carnivores. At the producers' level, solar energy is converted into chemical energy through photosynthesis. The same energy flows along with food from the producers through herbivores and various levels of carnivores.
In a difficult-to-digest nut shell, energy transfer through an ecosystem is restricted by the ability of primary producers to convert solar energy, and the ability of consumers to take in the energy they obtain as biomass. Ultimately, only 10 percent of energy is transferred from one trophic level to the next.
Most of the well-documented effects of solar energy on ecosystems and biodiversity manifest through the loss and change of habitats. This is because the development of solar energy infrastructure can take up significant amounts of land modifying and fragmenting habitats in the process.
An ecosystem is an energy system – a solar-powered system. The energy enters through photosynthesis and is stored in plants. Plants also pick up nutrients from the soil, water, and atmosphere. Nutrients and energy contained in the plants flow into animals through the food chain.
Therefore, in order to sustain life, energy must be available within an ecosystem. The initial source of energy for almost every ecosystem on Earth is the sun: Solar energy is converted into biomass by primary producers and is then transferred between trophic levels from one consumer to the next up the food chain.
The energy flow through an ecosystem presents two basic features, viz.: 1. Energy flow is always unidirectional. The biochemical energy in the autotrophs or producers flows towards herbivores and carnivores. The reverse flow, that is, from top carnivores to herbivores and from herbivores to autotrophs, is impossible to happen. 2.
In conclusion, solar energy generates electricity by harnessing the power of the sun's rays and converting them into usable electricity through the use of solar panels and photovoltaic cells.
How Does Solar Power Create Electricity? Solar power generates electricity by using either solar thermal systems that convert sunlight into heat to produce steam that drives a generator, or photovoltaic systems, which transform sunlight into electricity through the photovoltaic effect.
solar power, form of renewable energy generated by the conversion of solar energy (namely sunlight) and artificial light into electricity. In the 21st century, as countries race to cut greenhouse gas emissions to curb the unfolding climate crisis, the transition to renewable energies has become a critical strategy.
In the first quarter of 21st century, solar power was the third most widely utilized form of renewable energy after hydroelectric power and wind power; in 2022 it accounted for about 4.5 percent of the world's total power generation capacity. The majority of the world's solar power comes from solar photovoltaics (solar panels).
Yes, it can – solar power only requires some level of daylight in order to harness the sun's energy. That said, the rate at which solar panels generate electricity does vary depending on the amount of direct sunlight and the quality, size, number and location of panels in use.
There are several ways to turn sunlight into usable energy, but almost all solar energy today comes from “solar photovoltaics (PV).” Solar PV relies on a natural property of “semiconductor” materials like silicon, which can absorb the energy from sunlight and turn it into electric current.
Solar energy is a form of carbon-free, renewable energy, in which sunlight is turned into electricity, heat, or other forms of energy we can use.
Through a remarkable process known as the photovoltaic effect, PV cells—the building blocks of solar panels—absorb photons from sunlight, exciting electrons and generating an electric current.
Photovoltaics is a form of renewable energy that is obtained from solar radiation and converted into electricity through the use of photovoltaic cells. These cells, generally made of semiconductor materials such as silicon, capture photons of sunlight and generate electrical current.
Solar PV, or photovoltaic solar energy, is the type of solar energy that is produced on rooftops of homes and businesses to generate electricity directly from solar energy. Solar thermal technologies, on the other hand, use the sun's energy to generate heat, and electricity is then produced from that. Australia receives thousands of times more solar energy from the sun each year than all fossil fuel use combined.
A photovoltaic (PV) cell, commonly called a solar cell, is a nonmechanical device that converts sunlight directly into electricity. Some PV cells can convert artificial light into electricity. Sunlight is composed of photons, or particles of solar energy.
Solar power is generated in two main ways: Solar photovoltaic (PV) uses electronic devices, also called solar cells, to convert sunlight directly into electricity. It is one of the fastest-growing renewable energy technologies and is playing an increasingly important role in the global energy transformation.
The literal translation of the word photovoltaic is light-electricity—and this is exactly what photovoltaic materials and devices do—they convert light energy into electrical energy. PV systems generate power without pollution—and recent advancements have greatly improved their efficiency and electrical output.
Sunlight, consisting of small packets of energy termed as photons, strikes the cell, where it is either reflected, transmitted or absorbed. When the photons are absorbed by the negative layer of the photovoltaic cell, the energy of the photon gets transferred to an electron in an atom of the cell.
In general, you'll save more money quicker with solar if it's replacing more expensive energy, but that's also dependent on how much energy you use and the policies that support or deter.
Traditional solar panels: Monocrystalline solar panels are the most common among homeowners. These panels offer the best efficiency and power output but are the most expensive. Polycrystalline panels cost slightly less but are also less efficient, so you must buy more panels to power your home.
Originally published in the March/April issue of Solar Today . Within the solar industry, it's common knowledge that the optimal orientation of solar photovoltaic (PV) panels in the Northern Hemisphere is typically south, to maximize electricity production over the life of the system.
Going solar also allows you to rely less on external electricity sources and gain protection from unforeseen disruptions in the power supply. Federal and state solar incentives help reduce initial installation costs, resulting in a better return on investment.
Federal and state solar incentives help reduce initial installation costs, resulting in a better return on investment. More than 3 million homes have reaped these benefits by converting to solar energy, with one million installations taking place in the last two years, according to the U.S. Department of Energy.
South-facing systems produce the most energy earlier in the day, while west-facing peak production is focused later in the day, coinciding more closely with peak electricity load during this period. In the case of Friday, August 22, the peak load occurred at approximately 6:00 p.m. local time.
Though expensive to install, solar panels are worth the investment for most users. They offer several benefits, including long-term cost savings and increased home value. Going solar also allows you to rely less on external electricity sources and gain protection from unforeseen disruptions in the power supply.
Follow These Steps to Disconnect Solar Panels:Check to see if your system has a disconnect switch. If not, cover the solar panels with a reflective or opaque surface. Use a voltage or multimeter to make sure the voltage measures zero. Remove the bolts and clamping devices, if applicable.
As you are aware of how to safely disconnect solar panels, let us learn about disconnecting panels from the grid. The only way to completely disconnect your solar system from the grid is if you additionally install a battery backup system.
A solar AC disconnect separates the solar inverter from the electric grid, allowing alternate current (AC) power to be safely shut off if necessary. An AC disconnect is generally mounted to the wall between the utility's meter and the solar inverter, and can either be a separate switch or a breaker in an electric service panel.
However, homeowners may need to disconnect their solar panels for a variety of reasons, making it critical to fully grasp the process. The disconnection can occur due to incoming storms that could damage the system, residence relocation, periodic maintenance, module replacements, or even system upgrades.
A solar DC disconnect (or PV disconnect) shuts off the direct current (DC) power traveling from the solar panels to the inverter. DC disconnects are often built into the solar inverter. Do I need a solar disconnect switch? Local ordinances and building codes require AC and DC disconnects in all solar installations.
A solar panel quick disconnect is a simple maneuver that can be carried out. To accomplish this, safety equipment must be worn, the AC/DC disconnect switch must be turned off, the panels must not be producing power, the voltage must be checked, and finally, the MC4 connectors and mounting hardware must be unplugged.
Disconnecting a solar panel is an easy process and it doesn't require a lot of tools. However, disconnecting a solar panel and uninstalling it can lead to a wide range of problems. Leaving a panel disconnected for a long period of time can lead to a reduction in its lifespan.
Farmers can benefit from solar energy in several ways—by leasing farmland for solar; installing a solar system on a house, barn, or other building; or through agrivoltaics.
A DC surge protection device (SPD) protects your system from overvoltage due to lightning strikes or unusual high voltage spikes from the grid. In this article, I will talk about installing a surge protection device for solar panels. You size the surge protection device according to the voltage of your solar array, whether its wired in series or parallel. Let's say the combined voltage of your solar array is 500VDC; then, you need to get an SPD rated at 500VDC. There are many 1000VDC. Do solar isolators need to be double or single pole? I have written an article about it: Do solar isolators need to be single or double pole? Wiring an SPD is relatively easy. After your solar disconnect, take the positive and negative and bring it to the input of the SPD device. The output of.
Recent changes to the BS7671 UK Wiring Regulations 18th Edition in the form of amendment 2 have introduced requirements and considerations for surge protection on both the AC and DC side of a solar PV System.
It is compulsory to install SPD (surge protection devices) at the ac output of a single phase and three-phase solar inverters. The surge protection module will protect the inverter from high voltages that might be detrimental for the MOSFET and IGBT (internal semiconductors). We recommend the following devices with din-rail mounting.
In a photovoltaic system, the placement and quantity of Surge Protective Devices (SPDs) on the DC side are determined by the cable lengths between the solar panels and the inverter. If the cable length is under 10 meters, it is sufficient to install an SPD near the inverter.
Use SPDs that are specifically designed for DC applications on the DC side and for AC applications on the AC side is crucial to effective protection. When multiple inverters are connected to a single grid, they can be linked to a single PV surge protective device placed upstream for optimal protection.
As the installations and demand for PV systems increases, so does the need for effective electrical protection. PV systems, as with all electrical power systems, must have appropriate overcurrent protection for equipment and conductors.
In the event of lightning strikes, proper surge protection can prevent your valuable PV solar panels and inverters from formidable damage. Installing SPDs on both AC and DC lines on your system is key, especially considering the high cost of inverters within a PV system.
Solar energy is the from the 's and, which can be harnessed using a range of such as, (including ) and. It is an essential source of, and its technologies are broadly characterized as either or active solar depending on how they capture and distribut.
The Solar energy to the Earth refers to this energy that hits the surface of the Earth itself. The amount of energy that reaches the the Earth provides a useful understanding of the energy for the Earth as a system. This energy goes towards weather, keeping the temperature of the Earth at a suitable level for life, and powers the entire biosphere.
Solar energy acts as a primary energy flow that can be harnessed. Almost all of the Earth 's energy input comes from the sun. Not all of the sunlight that strikes the top of the atmosphere is converted into energy at the surface of the Earth. The Solar energy to the Earth refers to this energy that hits the surface of the Earth itself.
Solar energy refers to the radiant energy emitted by the sun, which is harnessed through solar panels to produce electricity or heat. It is a natural, sustainable, and renewable energy source readily available on our planet. Our ancestors recognized its potential, utilizing it in various forms even in ancient times.
Let's explore some of the exciting ways solar is already being used today: Residential: With solar panel technology, homeowners are harnessing renewable energy to power their lives, transforming rooftops and yards into eco-friendly energy hubs. Best of all, they're slashing their energy bills in the process.
It plays a substantial role in achieving sustainable development energy solutions. Therefore, the massive amount of solar energy attainable daily makes it a very attractive resource for generating electricity.
Reliable and Diverse Uses: Solar energy is versatile and a reliable source for various applications, such as cooking, lighting, transportation, and industrial processes. 1. Industrial Applications Industries benefit from solar energy by installing solar power system on their roofs to power heavy machinery and protect infrastructure from corrosion.
According to the installation method, it can be divided into floor-mounted charging piles and wall-mounted charging piles. Floor-mounted charging piles are suitable for installation in parking spaces that are not close to walls. According to the installation location, it can be divided into public charging piles and special. 1. It can provide convenient fast charging service for electric vehicles. The use of charging piles can help all electric vehicles to complete fast charging services, and no matter how far the speed. First of all, the cost of AC charging piles is low, the construction is relatively simple, and the load requirements on the transformer are not large, and the power distribution cabinets in the.
Lithium-ion – particularly lithium iron phosphate (LFP) – batteries are considered the best type of batteries for residential solar energy storage currently on the market. However, if flow and saltwater batteries became compact and cost-effective enough for home use, they may likely replace lithium-ion as the best solar batteries.
Solar or photovoltaics (PV) provide the convenience for battery charging, owing to the high available power density of 100 mW cm −2 in sunlight outdoors. Sustainable, clean energy has driven the development of advanced technologies such as battery-based electric vehicles, renewables, and smart grids.
m) The protection level of the charging pile (bolt) complies with the IP54 requirements of “GB 4208-1993 Enclosure Protection Level (IP Code)”; The input end of the charging pile is directly connected to the AC grid, and the output end is equipped with a charging plug for charging the electric vehicle.
Conventional design of solar charging batteries involves the use of batteries and solar modules as two separate units connected by electric wires. Advanced design involves the integration of in situ battery storage in solar modules, thus offering compactness and fewer packaging requirements with the potential to become less costly.
Charging piles generally provide two charging methods: conventional charging and fast charging. People can use a specific charging card to swipe the card on the human-computer interaction interface provided by the charging pile to perform corresponding charging operations and cost data printing.
As the electric vehicle charging pile (bolt) on the power distribution side of the power grid, its structure determines that the characteristics of the automatic communication system are many and scattered measured points, wide coverage, and short communication distance.
Renewable energy systems, such as photovoltaic (PV) systems, have become increasingly significant in response to the pressing concerns of climate change and the imperative to mitigate carbon emissions. Whe. The world's interest in renewable energy is attributed to several reasons. First, many. The ability of systems to predict energy production and consumption allows for excellent optimization and efficiency. By using machine learning algorithms to analyze historica. Integrating renewable energy sources into power grids and buildings is crucial for sustainable energy use. In this context, PV systems have become popular due to their proven effectiven. The energy management of PV systems is an important issue when studying renewable energy. One of the methods to control this process is by using an ANN. ANN-based contr. Fig. 12 shows the idealized discharge characteristics of two series-connected 200Ah, 12 V, and 10C lead-acid batteries for loads of 400 W, 500 W, and 600 W are 16.667A, 20.833.
[PDF Version]The load linked to the system is kept constant during this procedure. The energy management of PV systems is an important issue when studying renewable energy. One of the methods to control this process is by using an ANN.
Home Assistant, an open-source home automation software, might just be the solution. This article will explore how integrating Home Assistant can streamline the management of your solar panels and battery systems. Home Assistant makes monitoring and managing solar and battery systems simple by putting all controls in one place.
We show you how to get the most out of your PV system using intelligent energy management. To exploit the savings potential of your photovoltaic system to the full, it's The best way to do this is, for which, first and foremost, you will need a smart electricity meter like the Fronius Smart Meter. A captures data on
The energy management of PV systems is an important issue when studying renewable energy. One of the methods to control this process is by using an ANN. ANN-based controllers are gaining popularity due to their ability to adapt to different scenarios and enhance energy conversion efficiency.
In addition, it enables the user to perform intelligent household energy allocation, optimize household load allocation in the time dimension, achieve customer demand response, relieve grid pressure during peak hours, and improve grid stability. Solar PV is extensively employed in smart homes due to its ease of installation and inexpensive cost.
Many aspects of PV systems should be taken into consideration, including (but not limited to) the intelligent control of power converters, the intelligent operation and protection control system, and the intelligent sensing and detection technologies.
Buying solar you don't need or won't use is the most obvious error. Your batteries will recharge just as well and probably faster using the power at your destination.
If your RV solar panels aren't generating enough power, it can be frustrating—especially if you rely on them for daily use. This issue can arise due to a few different factors. Solution: Make sure your solar panels are clean and free of dirt or debris, as this can block sunlight.
Buying RV solar panels you don't need or won't use Buying solar you don't need or won't use is the most obvious error. If all you do is travel from RV park with hookups to RV park with hookups, you don't need solar panels to recharge your batteries. Your batteries will recharge just as well and probably faster using the power at your destination.
Solar panels in RVs do not directly provide electricity to run your 120V appliances such as Air Conditioning, Microwave, electrical outlets, etc. Instead, they charge your RV's batteries. That's it. Solar panels are simple and fairly efficient in good direct sunlight.
Solar panels charge RV batteries. That's it. They are simple and fairly efficient in good direct sunlight. The more panels, the faster your batteries charge back up.
Electrical problems can happen with RVs, and as many RV components rely on electrical power to work, you won't be able to do much in a rig that doesn't have any power. So let's take a look at the causes of an RV that's plugged in but with no power.
If you want a solar power system, a solar meter is a must. Check the Breaker Switch. The breaker switch is the small container that controls electrical flow in your RV. A system overload, damage or glitch can cause the breaker switch to trip. This prevents solar power from reaching your appliances.
Contact our team for a free feasibility study and custom quote for your smart energy or digitalization project.